12-pounder ball question

Steve53

Cadet
Joined
Oct 20, 2026
Location
NE
I recently came upon this long-forgotten item. It's been sitting in a corner for something more than 30 years. Diameter is correct for a 12-pounder and it weighs 12.65 pounds. Does the attached photo tell us anything in terms of its contents and safety? Is that a plug inserted after being disarmed? It was in this house before I got here. Long story short, my wife was in the antique business and she and her former husband picked up all sorts of stuff from many sources. She thinks they bought this locally (Lincoln, Nebraska) from a guy who also sold them a 2-pound and 3-pound shot. That's the only provenance we have. Any possibility that this thing is dangerous?

20261021_134001.webp
 
With no explosive inside, right? Perfectly safe as long as I don't drop it on my foot. Correct?
 
I recently came upon this long-forgotten item. It's been sitting in a corner for something more than 30 years. Diameter is correct for a 12-pounder and it weighs 12.65 pounds. Does the attached photo tell us anything in terms of its contents and safety? Is that a plug inserted after being disarmed? It was in this house before I got here. Long story short, my wife was in the antique business and she and her former husband picked up all sorts of stuff from many sources. She thinks they bought this locally (Lincoln, Nebraska) from a guy who also sold them a 2-pound and 3-pound shot. That's the only provenance we have. Any possibility that this thing is dangerous?

View attachment 593007

Three pound & two pound round steel balls are typical of a ubiquitous commercial product.

You have what is known as a "mill ball." The circular mark is from the "sprue" through which molten metal entered the mold from which it was cast. They are very often mistaken for cannon balls. For a modern example read more here.

Link


XXXX

Grinding mills have used balls for pulverizing ore, clay, minerals & all manner of materials have been used for thousands of years. For modern ball mills read more here.

LINK


XXXXXXX

Weight & dimension of 12 pound cannon balls. No sprue mark & smooth exterior so that it would fly straight. Read more here.

Link

 
Last edited:
Sooooo, it's NOT a cannon ball. We'll, that's disappointing, though it's good to know that it isn't going to explode.
 
Sooooo, it's NOT a cannon ball. We'll, that's disappointing, though it's good to know that it isn't going to explode
Don't rule out a cannon ball. Because 12 pound cannon balls can have a sprue mark. They are just usually shaven down to make it smooth. But a crude poor can definitely happen with low resources. Only thing that is a little odd is the perfectly round divot. Almost like it was made like that. If you have calipers can you measure it.

IMG_8436.webp
 
The diameter of the divot right where it breaks from the surface is 1.15 inches. The diameter of the ball is 4 and 5/8 inches. The attached photo shows what is opposite the divot. I should have shown that before, but I was most concerned about what looked like a plug. I don't know if the molded figure is 1 and 1/2 or not. I shouldn't even read AI, but when I put in that photo it said that after the war, the army distributed tons of surplus cannon balls for memorials. So a cemetery would have a cannon and a pyramid of cannon balls next to it. It speculated that the figure could be some kind of category designation. I can't imagine what "1 1/2" would indicate. It doesn't correspond to any weight or size in any system I can think of. It would also be odd if that was "melted" into the ball after the initial casting, considering the temperature necessary, so I doubt that it was some post-war operation done in preparation for shipping it someplace for a memorial. And the "1" looks more like a bar than a numeral one. Did milling balls have some kind of designation molded into them? Anyway, thanks for any insight anybody can provide.

17929027401986468588148382722446.webp
 
The diameter of the divot right where it breaks from the surface is 1.15 inches. The diameter of the ball is 4 and 5/8 inches. The attached photo shows what is opposite the divot. I should have shown that before, but I was most concerned about what looked like a plug. I don't know if the molded figure is 1 and 1/2 or not. I shouldn't even read AI, but when I put in that photo it said that after the war, the army distributed tons of surplus cannon balls for memorials. So a cemetery would have a cannon and a pyramid of cannon balls next to it. It speculated that the figure could be some kind of category designation. I can't imagine what "1 1/2" would indicate. It doesn't correspond to any weight or size in any system I can think of. It would also be odd if that was "melted" into the ball after the initial casting, considering the temperature necessary, so I doubt that it was some post-war operation done in preparation for shipping it someplace for a memorial. And the "1" looks more like a bar than a numeral one. Did milling balls have some kind of designation molded into them? Anyway, thanks for any insight anybody can provide.

View attachment 593292

Mill balls are 1/2" to 36" in diameter depending on application. They are made with ceramics & various metals depending on application. The finish runs from exquisite mirror to rough, untouched foundry surface.

Exactly why casting 1 1/2 into a ball would be done is a mystery. However, iron mill balls do have wear marks cast into them.

For how & why that is done, read more here.


Link

 

Learn About Us
►About CivilWarTalk
►Contact the Webmaster
►Meet the Staff
►Link to CivilWarTalk
Join Our Community
►Register
►Browse Forums
►View Today's Discussions
►Search the Forum
Get Help
►FAQ
►Student Guide
►Forum Rules & Etiquette
►Copyright / DMCA

     Contact Us CivilwarTalk on Facebook CivilWarTalk on YouTube CivilWarTalk on Twitter RSS Feed

Bringing the American Civil War and More to Life.
© 1999 - , CIVILWARTALK, LLC - Site Version 10.0

SlaveryTalk.com - SecessionTalk.com - CivilWarTalk.com - ReconstructionTalk.com
Back
Top